Questions?

telephone icon

Call 888 847 6552

PRESS RELEASE FOR IMMEDIATE RELEASE – Q4 2016

For Editors

Step-up Your Safety and Escalate Your Reputation

Step-Up-Your-Safety-With-Elestas-SIS212-Forcibly-Guided-Safety-Relays  

pdf

Printable Press Release

pdf

Example Datasheet - SIS212




SIS Series & MORE Forcibly Guided Safety Relays

Escalate your reputation for safety with Elesta’s reliable forcibly guided safety SIS Series PCB Relays from American Electronic Components Inc. (AEC) www.aecsensors.com! These compact and most energy efficient force guided SEN type relays (Sensitive, meaning the coil takes less current to actuate than “standard” type) include the smallest forcibly guided (safety) relays currently available on the market: Each features an innovative notch-crown contact system with a sensitive coil, which renders the relay capable of impressive current switching extremes as low as 3mA and as high as 6A/250VAC.

Fully compliant with DIN standard IEC/EN61810-3 type ‘A’, the SIS Series force guided relays operate with category III protection over voltage. These safety PCB relays incorporate contacts from 1NO+1NC to 4NO+2NC enabling equipment to be designed to comply fully with safety standards.

Bruce Finke, VP Sales & Marketing at AEC commented “The smallest relay in the SIS Series (SIS212) occupies a mere 7.85 cm3, with 3 forcibly guided contacts and is currently the smallest safety relay on the market worldwide. A distinct advantage with this relay and others in the SIS series is it can be used in the tightest of spaces, even where a cooling problem exists. The coil’s rated capacity is 0.4 Watt. While the relay responds at 0.22 Watt. The excitation voltage can subsequently be reduced even further. In reduced operation the relay operates with absolutely minimal inherent consumption (holding capacity) of as little as 0.05 Watt. This “low power” version enables the coil’s generation of heat to be kept at a very low level. Despite the low drive capacity, contact is maintained without loss on the contact side.”

A safe electrical separation exists between control and output side. Coil and control contacts are separated from the two output contacts by double and reinforced insulation, with clearance and creepage distances > 8mm. Large air gaps and tracking distances with accordingly high test voltage values, guarantee safe separation of the current circuits throughout the SIS Series. Coil low power dissipation ensures the circuit for relay activation can be kept simple with inexpensive components. The relay is installed directly on the printed circuit board with solder connections. The coil is monostable and of neutral execution. Coils can be produced for all common voltages from 3 to 110 VDC.

“At AEC we can provide all common coil voltages between 3 VDC and 110 VDC, with standard 0.6W or sensitive 0.4W coils. We also offer the full range of Elesta forcibly guided contact safety relays http://www.aecsensors.com/html/Forcibly-Guided-Safety/View-all-products.html which comprise 24 separate relay series, capable of switching currents from 3mA to 16A and can offer up to 10 contacts in a single relay. Please refer to our website for additional product details and contact us at This e-mail address is being protected from spambots. You need JavaScript enabled to view it if samples or prompt technical support are required:” continued Finke.

Elesta is the world’s foremost manufacturer of high quality forcibly guided relays, designed for public protection. Typical application areas for SIS3 relays include sensor technology, photoelectric cells, light curtains, elevators, escalators, foot mats, railways and frequency changers. All Elesta Relays are RoHs compliant and carry UL, cUL and TÜV approvals.

“With demand for smaller components constantly increasing, the SIS Series is unquestionably an apt and popular choice. Elesta relays should be considered wherever people or equipment must be protected and where a monitored contact is required.” Concluded Finke.

Editor Information

ABOUT American Electronic Component Incorporated

AEC is a leader in the design and manufacture of specialized electrical and electronic components primarily for automotive and industrial applications. Our product line includes positions sensors, G-force sensors, acceleration switches, DURAKOOL relays, push buttons, inclination sensors & switches and HERMASEAL glass to metal seals. Our creative engineering team has extensive experience in harsh environmental packaging concepts. We use high-quality products and are positioned to support your most challenging applications. AEC is ISO 9001 quality certified.

For further information please contact:

This e-mail address is being protected from spambots. You need JavaScript enabled to view it , Toll: 888 847 6552, Tel: +1 574 295 6330.

American Electronic Components, 1101 Lafayette Street, Elkhart, Indiana 46516, United States of America

Toll: 888 847 6552, Tel: +1 574 295 6330, Fax: +1 574-293-8013, sales@aecsensors.com

Developed by Paramount Web Technology